Care & Maintenance
Product Instructions
Husqvarna 2-stroke engines, including chainsaws, brushcutters, and leaf blowers, use gasoline mixed at 50:1 with Husqvarna 2-stroke oil. Use 20mL of oil per 1L of gasoline or 100mL per 5L. If the engine will not start, check old fuel, a clogged air filter, a wet spark plug, and the choke sequence in order. Sharpen the chain as soon as it becomes dull, and drain the fuel before storing the machine for more than one month.
Last updated
What is the correct mixing ratio for 2-stroke oil?
Husqvarna 2-stroke engines 50:1 with Husqvarna 2-stroke oil (XP, LS+, and others)is mixed with gasoline. Too little oil can score and seize internal engine components; too much can produce excessive smoke and leave deposits on the spark plug and exhaust port.
- Use unleaded gasoline and mix it in a clean fuel container.
- Add half the gasoline, then all the oil, then the remaining gasoline, and shake to mix.
- Mix only as much as you will use within one month, and shake it again before pouring it into the tank.
- For other brands of oil, follow the ratio printed on the container, and do not mix different oils.
- Chain oil is separateis a dedicated oil for lubricating the bar and chain. Fill the chain-oil tank with it, and top it up whenever you refuel.
| Gasoline | 2-Stroke Oil |
|---|---|
| 1L | 20mL |
| 2L | 40mL |
| 4L | 80mL |
| 5L | 100mL |
| 10L | 200mL |
How do I tension and sharpen the chain?
Adjusting tension
With the engine off and gloves on, slightly loosen the guide-bar nuts, lift the bar tip, and turn the tensioning screw. The chain until it does not sag below the bar Tighten it, but The chain should move around the bar when pushed by hand . After adjusting it, hold the bar tip up and retighten the nuts. A new chain stretches as it beds in, so check it frequently.
Signs that sharpening is needed
It is time to sharpen the chain if the saw produces fine powder instead of long chips, if you have to press down to make it cut, or if it cuts to one side. Sharpen every cutter at the same angle with the same number of strokes, and after several sharpenings, set the depth gauges (rakers) with a depth-gauge tool.
File diameter by chain
| Pitch | Chain example | Round file | Example models |
|---|---|---|---|
| 3/8" Mini (Low Profile) | S93G and others | 4.0mm | 135 Mark II |
| .325" | SP33G, S35G, and others | 4.8mm | 445S · 450S · 550XP Mark II · 560XP Mark II |
| 3/8" | C85 and others | 5.5mm | 565 · 572XP · 592XP |
These recommendations follow Husqvarna file-kit specifications. Check “Chain type” in the specifications table on the product page, and use the file kit for that chain number (including a round file, flat file, and depth gauge) for the most reliable result. For chains not listed in the table, contact us with the model name.
When should I clean the air filter?
The air filter removes sawdust and dust from air entering the engine. A clogged filter makes starting difficult, reduces power, and increases fuel consumption. Open the cover and shake out debris after use; clean or replace the filter if heavily soiled with oil. Some professional models use Air Injection technology to remove larger particles before they reach the filter, extending cleaning intervals.
How do I inspect the spark plug?
Remove the spark plug and inspect the electrode. If it is wet, the engine is flooded; let it dry, reinstall it, and try again. Replace the plug if it is blackened with soot or the electrode is worn. If the plug frequently becomes sooty, check for an incorrect fuel mixture with too much oil or a clogged air filter. Use a genuine plug specified for the model.
In what order should I troubleshoot a machine that will not start?
Many starting problems are fuel-related. Check each item in order from the top.
Fuel
Discard fuel mix that is more than one month old and prepare a fresh batch. Confirm a 50:1 mixing ratio.
Stop switch & choke
Check that the switch is in the ON position. For a cold engine, pull the choke and release it after the first firing sound. Follow the model-specific starting sequence in the operator's manual.
Flooding
Pulling the starter repeatedly with the choke engaged can wet the spark plug. Remove and dry the plug, or retry using the flooding-clearance procedure in the manual.
Air filter
If sawdust and dust clog the filter, starting and power will suffer. Tap it clean or wash it, and replace it if torn.
Spark plug
If the electrode is wet, blackened, or worn, replace it with the correct Husqvarna genuine spark plug for the model.
Fuel filter and hose
Check that fuel is flowing and the hose is not cracked.
Service Center
If it still will not start, carburetor adjustment and compression testing are required. Take it to the Head-office service center or a nearby Authorized Service Center.
If you added gasoline without mixing in oil, do not start the engine. Drain the fuel and contact a service center. Head-office service center 1577-6310 (ext. 2) · Customer Service 1577-6310 (ext. 1)
How should I store equipment that will not be used for one month or longer?
Drain the fuel and run the engine until it stops
After emptying the fuel tank, start the engine and let it run until it stops to remove fuel from the carburetor.
Cleaning
Brush off sawdust, grass residue, and oily grime, and clean dust from the air filter and between the cooling fins.
Bar and chain maintenance
Clean the bar groove and oil holes, sharpen the chain, and install the bar cover.
In a dry, secure place
Store in a dry place away from ignition sources and out of children's reach.
Before using it again
Add freshly mixed fuel, check the spark plug, air filter, and chain brake, and then start the engine.
How often should consumables be replaced and inspected?
These are general guidelines based on the maintenance schedules in Husqvarna operator’s manuals. Follow the operator’s manual for your model for the exact service intervals.
Before and after use (daily)
- Check chain-brake operation
- Check chain cutters and tension; sharpen if dull
- Clean the guide-bar groove and oil hole; verify chain-oil flow
- Clean the air filter
- Check for loose screws and nuts and damage to handles and guards
- Brushcutter: check for blade cracks or missing teeth and inspect the guard
Weekly (with frequent use)
- Inspecting the spark plug
- Check starter rope and spring
- Clean engine cooling fins and the area around the starter
- Check sprocket wear
- Flip the guide bar and file down edge burrs
Monthly and before the start of the season
- Check fuel filter and fuel tank
- Clean around the clutch
- Check fuel hose and muffler
- Consider replacing the spark plug before the season
Consumables such as chains, guide bars, blades, filters, spark plugs and starter ropes wear out. Genuine consumables are Consumablescan be viewed at.
Product Instructions FAQs
What is the chainsaw oil mixing ratio?
The ratio is 50:1 for gasoline and Husqvarna 2-stroke oil. Add 20mL of oil to 1L of gasoline, or 100mL to 5L. For oil from another manufacturer, follow the ratio stated on the container, and do not mix different oils.
Can I use a 25:1 or 40:1 fuel-mixing ratio?
The standard ratio for Husqvarna 2-stroke oil is 50:1. Some oil types specify a different ratio, so follow the label on the oil container you are using. Too little oil can damage the engine, while too much increases smoke and deposits.
How long can mixed fuel be stored and used?
It is best to use fuel mix within one month. Old fuel mix is a common cause of starting problems, so mix only as much as you will use within one month.
Can I use engine oil or waste oil instead of chain oil?
Do not use it. Chain oil is specially formulated to adhere to the bar and chain. Other oils may provide insufficient lubrication, causing faster wear of the bar, chain, and sprocket.
The chain keeps stretching.
A new chain normally stretches while bedding in, so retighten it frequently. Also check that chain oil is flowing correctly. Continued stretching may indicate chain or sprocket wear and requires inspection.
The saw cuts to one side.
This occurs when the left and right cutters are sharpened unevenly or the guide bar is worn on one side. Resharpen both sides with the same number of strokes at the same angle, and dress or replace the bar.
It starts, then immediately stops.
Old fuel, a clogged air or fuel filter, and carburetor adjustment issues are common. If the problem remains after following the checks above, take the machine to a service center.
Where can I buy consumables?
Husqvarna genuine consumables such as chains, guide bars, files, oils, spark plugs, and air filters are available from the Husqvarna online store (husqvarna.co.kr) and Authorized Husqvarna Dealers nationwide. Provide the product model and required part information, and Customer Service at 1577-6310, extension 1 will confirm compatibility and availability.